Tag Archives: thin coat

Applying Render to OSB

How one should go about applying render to OSB is a question that we get asked on a near-daily basis. The simple answer is that applying render directly onto the OSB is not an ideal situation – it’s important to remember that at the end of the day, OSB is wood.

Nevertheless, there is a solution for rendering OSB, and we’re going to talk you through the best way you can do this!

Rendering OSB: Render Carrier Board

When rendering any substrate, especially when rendering OSB, consideration needs to be taken as to the suitability of the substrate for the materials that you are using. OSB is not completely waterproof and will inevitably absorb water from the basecoat, which can cause the wood to warp, eventually hindering structural integrity.

To avoid this, the best solution is to use a render carrier board. However, the render carrier board needs to be attached to battens, rather than to the OSB directly. This is because the two separate fabrics (the RCB board and the OSB) need ventilation between them to allow moisture to escape, and to avoid a situation where water builds up between the two materials. An air gap between the two is therefore necessary for the reduction of condensation.

The best course of action is to:

  • First, staple a breather membrane onto the OSB substrate – this will help prevent the build-up of condensation on the surface of the wood.
  • Next, install timber battens on top of the OSB (the positioning of the battens will depend upon the size of the render carrier board you are using).
  • Once these are in place, you can secure the render carrier boards onto the battens with wood screws.

The spacing of the boards will depend on the type of render carrier board you are using, but generally, you would leave 4-5mm between each board.

After the boards are in place, the gaps between them need to be covered over by a render carrier board tape. We recommend a tape that is breathable with a self-adhesive membrane, so it will prevent water vapour from gathering in the gaps between boards.

Basecoating the Render Carrier Boards

Render carrier boards don’t require priming because they are specially designed for being rendered, so you can go straight into applying the basecoat with no problems.

Although it is possible to use the 220 Basecoat Adhesive, we recommend using the 225 Premium Basecoat as a basecoat for extra strength and breathability. At this stage, the necessary beading required for the structure is sunk into the basecoat along with fibreglass mesh – remember to overlap each strip of fibreglass mesh by about 10-15cm.

Allow the basecoat to set for a period of 24-48 hours, before priming the basecoat with a Render Primer. The type of primer you use will depend upon the type of render, for example, if you were to render using Silicone Render (we recommend this one for buildings that require a high level of breathability), you would need to use our SiSi Render Primer. This can be painted on and then left to dry for 12 hours.

Rendering the Basecoat Layer

After all that essential preparation of the OSB and RCB boards, you are finally ready to render. Using our ready-to-use Silicone Render, apply it onto the substrate using a trowel. The render should go on at a thickness that matches the chosen grain size – for example, if you’ve chosen a 1.5mm grain size finish, then you should apply the render at 1.5mm thick.

Once distributed across the surface, rub up the surface of the render with a plastic render float to bring out the texture and achieve a consistent finish, then leave to dry for 24-48 hours. 

Struggling to chose a Silicone Render colour from our selection? Order a colour sample here.

 

Want to learn more? Come to one of the EWI Pro training centres!  More information found in the video below.

 

Approved Installers Request Form

Your Name*

Your Email*

Your Number*

Your Postcode

Additional Information

I would like to receive news and offers from EWI Store

Try before you buy with our Render Colour Samples

As if the entire home renovation process isn’t stressful enough, choosing the right colour and textured finish for the new façade of your home can be daunting. You want to choose a façade that will not only look good, but also last for years to come. That’s why, here at EWI Store, we offer both Silicone Render Colour Sample Pots and Render Colour Sample Charts to assist you in choosing the right façade for you! What’s more, our friends at EWI Pro also offer a Silicone Render Colour Sample Pouch! Read on to learn about each of these types of samples and how they will aid your decision in choosing the right render façade for you.

What is a Silicone Render Colour Sample Pot?

A Silicone Render Colour Sample Pot is a product available from EWI Store as a means of testing the colours of our silicone renders before making a purchase. The pots contain 750g of Silicone Silicate Render, our most popular silicone-based render, in a default grain size of 1.5mm; our most popular grain size.

Here at EWI Store, our renders are available in absolutely any colour – that’s right, any colour, including any RAL, NCS or Pantone shade. That’s a lot of choices, so, if you’re contemplating a colour, it’s wise to test it first!

We can offer our Silicone Render Colour Sample Pots in any colour of your choice; just let us know which colour you’d like to see, and our talented team will use our state-of-the-art mixing facilities to tint it for you!

Once the render from the sample has been applied, it needs at least 48-72 hours to dry and set to represent the final colour finish. Therefore, do not form a judgment of the colour when the product has only just been applied – give it a little time, and you will soon see your colour choice in all its glory!

What is a Render Colour Sample Chart?

A Render Colour Sample Chart is an EWI Pro product stocked at EWI Store that showcases real render swatches in a sturdy, compact booklet in our top 36 colours. It is a particularly handy resource for our installers to figure the best finish for their projects, but also offers a great means for seeing a range of colour options for your home. We always recommend choosing a few shades from our Render Sample Colour Chart before ordering a Pot or Pouch.

What is a Silicone Render Colour Sample Pouch?

A Silicone Render Colour Sample Pouch is available to order from our friends at EWI Pro to get a feel of the grain sizes we offer. The sample comprises a small plaque with the desired grain size, and it’s available to order for FREE! That’s right: you can simply put in a request to order a sample in the grain size of your choice, and they will be in touch to get the sample to you.

Our Silicone Render Colour Sample Pouches are available in 4 grain sizes: 1mm, 1.5mm, 2mm and 3mm. Each of these grain sizes presents a slightly different textured finish – the larger the grain size, the rougher the façade – which can also impact the final colour finish. Therefore, this sample allows you to see and feel what the final render façade could look like on your home!

Order one of our Samples today!

So, what are you waiting for? If you are looking to render your home, be sure to order a sample – be it a Silicone Render Colour Sample Pot, Silicone Render Colour Sample Pouch or Render Colour Sample Chart – and start making a decision today.

Still stuck for choice?

If you’re still stuck for choice or have any other questions regarding our render samples, colours or anything else, you can talk to one of our talented Sales Representatives who will be happy to recommend any colours and aid you in your decision. You can contact our team via email at [email protected] or by telephone at 02033974067. We’re always happy to help!

EWI Store are the leading UK render specialists, offering a range of high-quality Render and External Wall Insulation products. We take a whole-system approach to external wall insulation, stocking all the materials required to help installers achieve a stand-out result. Our selection of products is constantly growing as we strive to offer our customers the best possible choice of materials from trusted manufacturers and established brand names.

Monocouche Render vs. Silicone Renders

As you might have noticed, we offer a variety of advanced render systems here at EWI Store, the most popular being monocouche and silicone. Both monocouche and silicone render provide a decorative finish on the external walls of a property whilst also improving its thermal comfort. The result of the external appearance, however, greatly depends on the type of render chosen. In this blog, we discuss the main differences between monocouche and silicone render so that, if you are torn as to which one to choose for your renovation, we can assist in the decision-making process!

Monocouche Render

There are a wide variety of monocouche renders available on the market; here at EWI Store, we stock EWI Pro, K-Rend and Enewall. The key characteristic of monocouche render is that it is a through-coloured, thick-coat render. Monocouche render is very often compared to sand and cement render because it contains cement however, it is very different in terms of texture and characteristics.

Monocouche render tends to offer a chalkier finish than other renders. To provide the finished facade, the render is usually scraped to create a pitted effect. Available in a range of colours (natural and bright), it’s a very popular choice for homeowners who are looking to create a chalky, flat finish.

Silicone Render

Silicone render is a highly flexible, breathable and durable render that comes ready to use in 25kg buckets. Unlike monocouche render, silicone render is a thin-coat render, meaning it is applied very thinly on top of a reinforced basecoat. Although readily available in a standard white, silicone render can be tinted to absolutely any shade. Here at EWI Store, we have specialist tinting equipment that enables us to match to any RAL, NCS or Pantone colour, meaning we can cater to absolutely any taste. Silicone render can be used as a standalone system straight onto brick or applied onto external wall insulation boards to provide a decorative finish.

One of the main advantages of silicone render is that it is crack-resistant. The silicone properties within the render, coupled with the way it is applied, means that it is far less likely to crack than monocouche render.

Now that you know the difference between monocouche and silicone render, you might be wondering how much each cost to install. If so, we’ve got you covered: check out our blogs on monocouche scratch render cost per square metre here and coloured render cost per square metre here to get an idea as to how much you’re looking at.

We offer a variety of advanced silicone-based renders, including Nano Drex Silicone Render, Premium Bio Silicone Render, Silicone Render and Silicone Silicate Render. If you’re interested in trying any of these, be sure to give us a call and our lovely Sales Representatives will be happy to help!

If you’re looking for an approved installer to carry out the work for you, fill out the form below and we will be in touch. We upload blog posts every Tuesday and Thursday, so keep up to date with our blog and social channels to find out more!

Approved Installers Request Form

Your Name*

Your Email*

Your Number*

Your Postcode

Additional Information

I would like to receive news and offers from EWI Store

Replacing Pebbledash with Coloured Render

Pebbledash is perceived by many as an outdated look for a property; it was frequently used during the post-WW1 housing crisis as a means of covering up quickly-built, slap-dash properties. If you live in the UK, you are most likely to have come across a pebbledash building and, while it’s a durable building method, it’s definitely an acquired taste.

What is pebbledash?

The pebbledash effect is created by applying a layer of mortar (usually sand and cement) to an external wall and literally throwing pebbles at the wall. Pebbledash houses are still dotted all over towns and cities in the UK and can often have a somewhat dilapidated look. Over time, the pebbles can drop from the wall, leaving the mortar exposed to the weather and therefore vulnerable to absorbing water and causing damp issues. Also, due to its unpopularity, pebbledash can reduce the value of a property purely for its lack of aesthetic appeal. This is why coloured render is vastly more popular because it’s much nicer to look at. Our coloured renders can be customised to absolutely any colour of your choice and can be ordered online or over the phone!

How can I replace pebbledash with a coloured render?

While we’re not hating on pebbledash (much), you might want to consider re-rendering your property, whether you’re moving into a new home, updating the look of your current property or both. However, as one of our frequently asked questions here at EWI Store, we recognise that there is a knowledge gap on how to apply render on top of pebbledash. That’s why we’ve made this blog – to tackle the question for all you pebbledash homeowners!

The short answer is that, unfortunately, you cannot replace pebbledash with coloured render by applying coloured render directly on top of the pebbledash. Saying that, there are several ways around it that you may wish to consider.

Essentially, there are three possible options for removing pebbledash:

Option 1: Removing the pebbledash

The first option is to attempt to remove the pebbledash by hacking it off. However, the main downfalls to this option are that the brick underneath is at risk of being damaged, and there is no guarantee that you will achieve a smooth finish. If this is the best or only option for you, be very careful about who you hire to tackle the task; make sure they are experienced in removing pebbledash. If your pebbledash is forcibly removed, this can really damage the underlying wall and invalidate your house insurance. It’s also important to note that, even after all this, you still wouldn’t be free to apply coloured render directly on the wall. Building regulations stipulate that if you strip it right back to the original brick, then you’ll need to insulate before rendering with a coloured render.

Option 2: One Coat Dash Cover (OCDC) to cover up pebbledash

The second option is to use the One Dash Coat Cover (OCDC) to completely smooth over and cover up the pebbledash to achieve a clean slate. This product is specifically designed to be applied on top of pebbledash, and it can then be painted or rendered to achieve a modern appearance. The good thing about the OCDC is that it is breathable, so it will allow any trapped moisture within the underlying pebbledash to escape. It can also be applied up to 20mm in one pass (up to a maximum of 50mm), so it’s guaranteed to smooth over the pebbledash nicely!

Option 3: Insulate then render over pebbledash

A beneficial way of ridding the pebbledash look is by installing 20mm (or thicker, but the thicker you go, the more expensive) external wall insulation (EWI) boards over the top of your pebbledash. This is a great option because the EWI will give you added insulation, which can save you money on bills in the long run.

By installing EWI boards, you will also save time and money because hacking off the pebbledash won’t be necessary. Instead, you can simply secure insulation boards over the top of the pebbledash using adhesive and mechanical fixings. Once you have done this, you can apply the render of your choice on top of the insulation boards and achieve a far more pleasing outcome.

Which coloured render can I use to replace my pebbledash?

There are so many options for replacing your pebbledash with coloured render that it can be quite overwhelming. We want to give you a clear idea of what each coloured render can offer so that you can make the right choice to suit the needs of your property and your personal taste.

Thin Coat Coloured Renders to Replace Pebbledash

Thin coat renders are a great option for when removing your pebbledash and replacing it with coloured render. Because they are thin-coat, they offer a level of flexibility that ensures that your coloured render finish stays crack-proof for years to come. Thin coat coloured renders are also highly breathable, so they will help to prevent problems with damp and mould on your walls.

They also come in different grain sizes, which determines the textural finish that the coloured render will offer you – the bigger the grain size, the more textured the finish that you’ll achieve. If you have simply removed your pebbledash, then you may want to go for a larger grain size as this makes any imperfections in the basecoat less noticeable. Read our blog Coloured Render Cost Per M2 for an idea of pricing!

There are three options that you can choose for thin coat coloured renders:

  • Silicone render/Silicone Silicate render: Silicone Coloured Render is a premium, modern technology coloured render – which is available in hundreds of different colours. Silicone is a very popular choice because it offers hydrophobic properties – which means that it repels water, dirt and organic growth – so it probably requires about the same maintenance as pebbledash (very little). Silicone render is also super easy to apply because it comes ready to use, so you just apply it straight out the pot. (Read more about Silicone Render here).

 

  • Acrylic render: Acrylic Coloured render is very similar to silicone, except that it doesn’t provide the same hydrophobic properties. It’s a solid middle-ground thin coat render because it still provides the same flexibility, but it’s also great at holding onto colour pigment. This is a fantastic choice if you are looking to replace pebbledash with a coloured render. (Read more about Acrylic Render here).

 

  • Mineral render: Mineral Coloured render is a dry-mix, thin coat render. This is a very popular choice if you live in a cold or rainy climate (as many pebbledash homeowners do – Scotland, coastal homes!) because mineral render is extremely fast drying; you can’t apply other renders in cold/rainy temperatures because they take longer to dry. The only thing about this render is that you need to paint it afterwards with silicone paint to seal it in. This is because, if it’s left exposed to the elements, it can develop lime bloom due to the presence of Portland cement. (Read more about Mineral Render here)

Thick Coat Coloured Renders to Replace Pebbledash

Thick coat renders are far more traditional but, as the name suggests, they do lack flexibility and breathability because they are applied in a much thicker layer. Once you’ve removed your pebbledash, you can use our Monocouche Scratch Render. Note: thick coat renders aren’t suitable for application on top of insulation boards.

  • Monocouche scratch render: Monocouche scratch render is a thick coat, through-coloured render. It is more traditional, but does require extra work to install it. This is because the Monocouche needs to be applied in two passes for extra strength and cannot be applied in wet or humid conditions. Monocouche render then needs fibreglass mesh embedded within it to provide extra strength and flexibility (which means it will resist cracking) and then, once dried, it needs scratching back to achieve the desired texture. Read our blog Monocouche Scratch Render Cost Per M2 for an idea of pricing!

To conclude…

If you are a pebbledash homeowner, looking to re-render, or potentially even install EWI, then we have everything you will need. Check out our materials calculator or get in touch with us directly and we can point you in the direction of one of our fantastic approved installers!

Are you a fan of Pebbledash? Leave a comment below…

Let’s debate: pebbledash or no pebbledash? Leave a comment below with your opinion; is pebbledash outdated and ugly, or is it a relic from our past that we should preserve for traditional purposes? For those in favour of the pebbledash look, we might have something just for you.

 

Approved Installers Request Form

Your Name*

Your Email*

Your Number*

Your Postcode

Additional Information

I would like to receive news and offers from EWI Store